Free Pull Toy Plans: A Wooden Pull-Along Dog With Full-Size Template

This free plan makes a wooden pull-along dog on four wheels from one maple board and two dowels. It includes a full-size template, cut list, cutting diagram, drawings, steps, the small parts check and the US rules for selling toys, including pull cords. The PDF is free.

Categorized as Woodworking Business Tagged ,

This free plan makes a wooden pull-along dog: a 3/4 in. maple body on four 2-1/4 in. wheels, with a cotton pull cord and a dowel handle. The finished toy is 9-1/4 in. long and 4-15/16 in. tall. The wheels are glued to dowel axles that turn in the body, so there are no screws or metal parts. You can download the plan and full-size template as a printable PDF, with no sign-up.

The toy is designed for children aged 3 and up, and every part is larger than the CPSC small parts test cylinder. Pull toys appear in our list of wooden toys to make and sell. The build suits a beginner with a scroll saw or band saw and a drill press.

A plain maple pull-along dog on four wheels, with a cotton cord running to a dowel handle on a green rug.
The finished pull-along dog, left unfinished.

Wooden Pull Toy Plans at a Glance

PartNameQuantitySizeMaterial
ABody19-1/4 × 4-1/2 × 3/4 in.1 × 8 maple
BWheel42-1/4 dia. × 3/4 in.1 × 8 maple
CAxle23/8 dia. × 2-1/2 in.3/8 in. dowel
DHandle11 dia. × 4 in.1 in. dowel
EPull cord13/16 dia. × 26 in.Cotton cord
Finished size9-1/4 in. long × 4-15/16 in. tall × 2-1/2 in. wide
WoodHard maple (poplar works) and hardwood dowels
Ages3 and up
Skill levelBeginner to intermediate
Build timeAbout 3 hours, plus 24 hours for the glue (estimate)
FinishNone: leave the wood unfinished
Side view of the pull-along dog with its length, height and axle positions, and an end view of the axle and wheels.

Tools You Need

  • Scroll saw or band saw (a jigsaw works for the outline)
  • Drill press, with 13/32 in., 3/8 in. and 1/4 in. brad-point bits
  • Printer, scissors, and a glue stick or removable spray adhesive
  • Compass, square, tape measure and pencil
  • Fine-tooth handsaw or miter saw for the dowels
  • Sanding block or spindle sander; sandpaper in 120, 180 and 220 grit
  • Wood glue, a damp cloth and a scrap of thin card as a spacer
  • Wood-burning pen or stamp for the tracking mark
  • Safety glasses, hearing protection and a dust mask

Follow your saw and drill maker’s instructions, and clamp small parts rather than holding them by hand.

Materials

  • 1 × 8 × 2 ft. hard maple board (actual 3/4 × 7-1/4 in.): 1
  • 3/8 in. × 36 in. hardwood dowel (actual 3/8 in. diameter): 1
  • 1 in. × 36 in. hardwood dowel (or an offcut) (actual 1 in. diameter): 1
  • 3/16 in. (5 mm) cotton cord (actual 26 in.): 1

Choose a flat, straight board with no knots, cracks or splits. Do not use plywood, MDF or treated wood. Hardwood dowels are often a little over or under their stated size, so test-fit them in a scrap hole first.

The Full-Size Template

The PDF includes the body template at full size on one US Letter page, with the three hole centers marked. Print it at 100% (Actual size) and check its 1 in. test square before you cut. Draw the wheels with a compass.

A reduced view of the full-size pull-along dog body template, with crosses for the two axle holes and the cord hole.

Cutting Diagram

Cutting diagram: the dog body and four wheels on a 2 foot 1 by 8 maple board, with the axles and handle cut from dowels.

How to Make a Wooden Pull Toy, Step by Step

Step 1: Choose the Wood and Stick On the Template

Use solid hard maple, or poplar if you can’t find maple, with no knots, cracks or splits. Do not use plywood, MDF or treated wood. Print the full-size template at 100% (Actual size), check the 1 in. test square, and stick it to the board with the grain arrow along the board. Mark four wheel circles with a compass on the rest of the board.

Step 2: Drill the Holes

Drill every hole on a drill press while the board is still whole, with the board clamped flat so the holes are square to the face. In the body, drill the two axle holes at 13/32 in. and the cord hole at 1/4 in., right through. At the center of each wheel circle, drill a 3/8 in. hole right through. Use a scrap backer board so the far side does not split.

Step 2 diagram: the dog template on a maple board with two axle holes and a cord hole marked, and four wheel circles.

Step 3: Cut Out the Body and Wheels

Cut the body outline with a scroll saw or band saw, keeping just outside the line. Cut the wheels just outside their circles, then sand them round to the line on a disc or spindle sander. Cut two axles 2-1/2 in. long from the 3/8 in. dowel and the handle 4 in. long from the 1 in. dowel. Drill a 1/4 in. hole through the middle of the handle.

Step 4: Round the Edges and Sand

Peel off the paper and sand away any glue left on the wood. Round every edge of the body, wheels, handle and axle ends to about a 1/8 in. radius, and sand all faces with 120, 180 and 220 grit. Check that each axle turns freely in the body holes; sand the axle lightly if it binds.

Step 5: Fit the Wheels and Axles

Push an axle through the body. Put a little glue inside one wheel hole only, slide that wheel on until the axle end is flush with its face, and do the same on the other side. Keep a 1/8 in. card spacer between each wheel and the body while the glue sets, then pull it out. Keep glue out of the body holes: the axle must turn there. Let the glue cure for 24 hours.

Step 4 diagram: end view of the body, axle and two wheels, with glue only in the wheel holes and card spacers.

Step 6: Add the Cord and Handle

Cut 26 in. of 3/16 in. cotton cord. Thread it through the body’s cord hole and tie a stopper knot on the far side, larger than the hole. Thread the other end through the handle and tie a second stopper knot. That leaves about 24 in. of free cord. Pull hard on the handle to check that neither knot slips, then trim the tails short. Do not tie any loops in the cord.

Step 5 diagram: the pull cord from the body to the dowel handle, held by a stopper knot at each end.

Step 7: Check and Mark

Roll the dog across the floor: all four wheels should turn and touch the ground. Run your fingers over every edge and face for splinters. Burn or stamp your tracking mark on the underside of the body. Leave the wood unfinished.

Toy Safety and the Small Parts Check

Small parts check: the axle beside the 2-1/4 inch test cylinder, and the wheel and handle end compared with the opening.
  • Toys designed or sold mainly for children aged 12 and under are children’s products. The US Consumer Product Safety Commission (CPSC) regulates them, whatever the size of the business.
  • The toy safety standard ASTM F963 is mandatory (16 CFR Part 1250). It covers hazards such as sharp points and edges and small parts, and many tests follow drop, pull and twist (use and abuse) tests.
  • This plan is designed for ages 3 and up. Every part is too large to fit fully inside the CPSC small parts test cylinder, 1-1/4 in. wide and 2-1/4 in. long, so no choking hazard warning is needed for small parts.
  • Children’s products need third-party testing at a CPSC-accepted lab and a Children’s Product Certificate (CPC). Small batch manufacturers who register with the CPSC get relief from some third-party tests, but not all.
  • The CPSC has determined that unfinished, untreated solid wood does not need third-party testing for lead content or the heavy metals in ASTM F963. Paint, stain, varnish and other finishes or treatments remove that exemption, and paint and surface coatings must not exceed 90 ppm lead.
  • Each toy needs a permanent tracking label on the toy and its packaging, where practical: who made it, where, when and the batch.
  • ASTM F963 has extra rules for cords on toys for children under 3, and pull toys are often bought for toddlers. For toys meant for children under 36 months, a pull cord longer than 12 in. must not have beads or other attachments that could form a loop. This plan is designed for ages 3 and up and has no loops, but if you want to sell it for younger children, ask your testing lab which cord rules apply.

Selling Wooden Pull Toys

Pull toys are children’s products, so the rules above apply before you sell them, including at craft fairs and on marketplaces. Leaving the wood unfinished keeps the exemption from lead and heavy-metal testing for the wood. The cord and glue are separate materials, so ask your testing lab about them.

The lab’s use and abuse tests pull on parts, so test the cord knots and the glued wheels on your own samples first. Pack the toy with the cord coiled, in a bag or box printed with your tracking label details.

This is a summary to help you plan. It is general information, not legal advice. Read the CPSC pages listed under Sources, or ask the CPSC Small Business Ombudsman, before you sell.

See how to set the final selling price on your craft and how to sell woodworking projects. The top 10 woodcrafts to sell has more ideas.

Download the Printable Wooden Pull Toy Plans

The PDF has 9 pages on US Letter paper, with the full-size template, cut list, cutting diagram, drawings, steps and the toy safety summary. It is free, with no sign-up.

Download the pull toy plans (PDF)

Build status: plan checked by calculation; not yet test-built. Facts checked: November 2026.

Sources


Discover more from AssembleAndEarn.com

Subscribe to get the latest posts sent to your email.

Leave a comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.