These free wooden puzzle plans make a farm-scene tray puzzle with 13 chunky pieces: a barn with a door that lifts out, a cow, a sheep, a pig, a tree, the sun and a cloud, plus the sky, the hills and the meadow around them. The pieces are cut from one 3/4 in. maple blank on a scroll saw and sit in a tray made from a plywood backing and a glued-on border. You can download the plan and full-size template as a printable PDF, with no sign-up.
The puzzle is designed for children aged 3 and up, and every piece is larger than the CPSC small parts test cylinder. The animals have flat bottoms, so they stand up on their own. Puzzles appear in our list of wooden toys to make and sell.

Wooden Puzzle Plans at a Glance
| Tray size | 10-1/16 × 8-5/16 in. |
|---|---|
| Pieces | 13, all 3/4 in. thick; they stand 1/4 in. above the border so they are easy to lift |
| Wood | Hard maple for the pieces (poplar works), a 1/2 in. poplar hobby board and 1/4 in. plywood for the tray |
| Ages | 3 and up |
| Skill level | Intermediate |
| Build time | About 4 to 5 hours, most of it cutting and sanding (estimate) |
| Finish | None: leave the wood unfinished |

Cut list
| Part | Piece | Size (width × height × thickness) |
|---|---|---|
| A | Sun | 1-5/8 × 1-5/8 × 3/4 in. |
| B | Cloud | 1-15/16 × 1-1/8 × 3/4 in. |
| C | Sky, left | 3-3/4 × 3 × 3/4 in. |
| D | Sky, right | 4-1/4 × 3 × 3/4 in. |
| E | Tree | 1-13/16 × 2-1/4 × 3/4 in. |
| F | Barn | 2-1/4 × 2-1/8 × 3/4 in. |
| G | Barn door | 1 × 1-1/16 × 3/4 in. |
| H | Hills | 5-1/8 × 1-3/8 × 3/4 in. |
| J | Cow | 2 × 1-11/16 × 3/4 in. |
| K | Sheep | 1-3/4 × 1-1/2 × 3/4 in. |
| L | Pig | 1-7/16 × 1-7/16 × 3/4 in. |
| M | Meadow, left | 5-7/16 × 2-1/2 × 3/4 in. |
| N | Meadow, right | 2-5/8 × 3-5/16 × 3/4 in. |
| Part | Tray part | Qty | Size (T × W × L) | Material |
|---|---|---|---|---|
| P | Backing | 1 | 1/4 × 8-5/16 × 10-1/16 in. | 1/4 in. plywood |
| Q | Border, long | 2 | 1/2 × 1 × 10-1/16 in. | 1/2 × 3-1/2 in. poplar hobby board |
| R | Border, short | 2 | 1/2 × 1 × 6-5/16 in. | 1/2 × 3-1/2 in. poplar hobby board |
Tools You Need
- Scroll saw with #5 or #7 reverse-tooth blades
- Table saw or miter saw, for the blank and the border strips
- Drill with a 1/16 in. bit (one blade hole for the cloud)
- Square to set the scroll saw table at 90° to the blade
- Printer, scissors, and a glue stick or removable spray adhesive
- Wood-burning pen, or a V-gouge, for the detail lines
- Clamps or weights for gluing the tray
- Sanding block, files, and sandpaper in 120, 180 and 220 grit
- Safety glasses, hearing protection and a dust mask
Follow your saw maker’s instructions, and keep your fingers to the side of the blade, not in line with it.
Materials
- 1 × 8 × 2 ft. hard maple board (pieces for two puzzles) (actual 3/4 × 7-1/4 in.): 1
- 1/2 × 3-1/2 in. × 4 ft. poplar hobby board (borders for two trays) (actual 1/2 × 3-1/2 in.): 1
- 1/4 in. plywood project panel, 2 × 4 ft. (backings) (actual about 1/4 × 24 × 48 in.): 1
- Wood glue (PVA), for the tray only
Choose flat, straight boards with no knots, cracks or splits where the pieces will be. The pieces need no glue, screws or finish.
The Full-Size Template
The PDF has the template at full size on one US Letter page. Print it at 100% (Actual size) and check its 1 in. test square before you cut. Black lines are cut lines; orange lines are details to burn or carve.

Cutting Diagram


How to Make a Wooden Farm Puzzle, Step by Step
Step 1: Choose the Wood and Cut the Blank
Use solid hard maple, or poplar if you can’t find maple, with no knots or cracks. Cut a blank 8 × 6-1/4 in. with the grain running the long way, and square its corners. A 2 ft. board gives two blanks.
Step 2: Stick the Template On
Print the template at 100% (Actual size) and check the 1 in. test square. Trim the paper to the blank rectangle and stick it on with a glue stick or removable spray adhesive, lining the rectangle up with the edges of the blank.
Step 3: Cut the Pieces Apart
Square the scroll saw table to the blade. Cut the long lines first, from the edge: the hill line, the field line (it ends at the barn), the line up from the bottom edge into the barn, and the line down from the top edge to the tree. Then cut round each figure, starting where a line or an edge meets it. Cut the barn door last, from the barn’s bottom edge. For the cloud, drill a 1/16 in. hole at the red dot, thread the blade through it and cut round.

Step 4: Burn the Details and Sand
Peel off the paper. Burn or carve the detail lines from the template: the barn doors and window, the faces, the cow’s spots and the legs. Round the top edges of every piece about 1/16 in. and the outside corners of the blank about 1/8 in. Sand every face with 120, 180 and 220 grit; keep the cut edges square so the pieces still fit.
Step 5: Make the Tray
Cut the backing (P) 10-1/16 × 8-5/16 in. from 1/4 in. plywood and the border strips (Q, R) 1 in. wide from the 1/2 in. hobby board. Glue the long strips along the top and bottom edges of the backing. Lay the puzzle in place, with a strip of thin card along one side and one end as a 1/32 in. spacer, then glue the short strips against it. Remove the puzzle before the glue sets.

Step 6: Round, Check and Mark
Round the tray’s outside edges and corners about 1/8 in. and sand it. Fit the pieces in and lift them out: each should drop in and come out easily. Run your fingers over every edge for splinters. Burn or stamp your tracking mark on the back of the tray. Leave the wood unfinished.
Toy Safety and the Small Parts Check
The model behind this plan checks every piece against the small parts test cylinder in every position, and checks that no piece is narrower than 1/2 in. anywhere, so no thin neck or point can snap off. The smallest piece, the barn door, is 1 × 1-1/16 × 3/4 in.
- Toys designed or sold mainly for children aged 12 and under are children’s products. The US Consumer Product Safety Commission (CPSC) regulates them, whatever the size of the business.
- The toy safety standard ASTM F963 is mandatory (16 CFR Part 1250). It covers hazards such as sharp points and edges and small parts, and many tests follow drop, pull and twist (use and abuse) tests.
- This plan is designed for ages 3 and up. Every part is too large to fit fully inside the CPSC small parts test cylinder, 1-1/4 in. wide and 2-1/4 in. long, so no choking hazard warning is needed for small parts.
- Children’s products need third-party testing at a CPSC-accepted lab and a Children’s Product Certificate (CPC). Small batch manufacturers who register with the CPSC get relief from some third-party tests, but not all.
- The CPSC has determined that unfinished, untreated solid wood does not need third-party testing for lead content or the heavy metals in ASTM F963. Paint, stain, varnish and other finishes or treatments remove that exemption, and paint and surface coatings must not exceed 90 ppm lead.
- Each toy needs a permanent tracking label on the toy and its packaging, where practical: who made it, where, when and the batch.
Selling Wooden Puzzles
Wooden puzzles for young children are children’s products, so the rules above apply before you sell them, including at craft fairs and on marketplaces. The tray’s glue and plywood backing are component parts of their own; ask your lab which need testing. Testing is per design, so cut every puzzle from the same template; a new scene is a new design.
A 2 ft. board makes two puzzles and a 4 ft. hobby board makes two borders, so build them in pairs.
This is a summary to help you plan. It is general information, not legal advice. Read the CPSC pages listed under Sources, or ask the CPSC Small Business Ombudsman, before you sell.
See how to set the final selling price on your craft and how to sell woodworking projects. The top 10 woodcrafts to sell has more ideas.
Download the Printable Wooden Puzzle Plans
The PDF has 11 pages on US Letter paper, with the full-size template, cut list, cutting diagram, tray drawing, steps and the toy safety summary. It is free, with no sign-up.
Download the wooden puzzle plans (PDF)
Build status: plan checked by calculation; not yet test-built. Facts checked: November 2026.
Sources
- The Home Depot, 1 in. × 8 in. × 2 ft. maple S4S board listing
- The Home Depot, 1/2 in. × 4 in. × 4 ft. S4S poplar board listing
- eCFR, 16 CFR Part 1250: Safety Standard for Toys
- US Consumer Product Safety Commission, Small Batch Manufacturers
- US Consumer Product Safety Commission, Small Parts and Choking Hazard Labeling FAQs
- US Consumer Product Safety Commission, Determinations Regarding ASTM F963 Elements in Unfinished and Untreated Wood
- US Consumer Product Safety Commission, Tracking Label Requirement for Children’s Products
- US Consumer Product Safety Commission, Component Part Testing
Discover more from AssembleAndEarn.com
Subscribe to get the latest posts sent to your email.
