Free Wooden Toy Car Plans: A Car and a Pickup Truck With Full-Size Templates

This free plan makes a wooden toy car and a pickup truck from one 2 × 4 poplar board, a 1 × 4 and a dowel. It includes full-size templates, cut list, cutting diagram, drawings, steps, the small parts check and the US rules for selling toys. The PDF is free.

Categorized as Woodworking Business Tagged ,

This free plan makes two wooden toys: a car 6 in. long and a pickup truck 8 in. long. Both bodies are cut from a 1-1/2 in. thick poplar 2 × 4, and they roll on 2 in. wheels glued to dowel axles that turn in the body. There are no screws or metal parts. You can download the plan and full-size templates as a printable PDF, with no sign-up.

The toys are designed for children aged 3 and up, and every part is larger than the CPSC small parts test cylinder. Cars and trucks appear in our list of wooden toys to make and sell. The build suits a beginner with a band saw or scroll saw and a drill press.

A plain wooden car and pickup truck on glued wheels, parked on a grey toy road over a light blue rug.
The car and the truck, left unfinished.

Wooden Toy Car Plans at a Glance

PartNameQuantitySizeMaterial
ACar body16 × 2-3/4 × 1-1/2 in.2 × 4 poplar
BTruck body18 × 3-5/16 × 1-1/2 in.2 × 4 poplar
CWheel82 dia. × 3/4 in.1 × 4 poplar
DAxle43/8 dia. × 3-1/4 in.3/8 in. dowel
Car6 in. long × 3-1/8 in. tall
Truck8 in. long × 3-5/8 in. tall
Width3-1/4 in. over the wheels
WoodS4S poplar boards and a hardwood dowel
Ages3 and up
Skill levelBeginner to intermediate
Build timeAbout 4 hours, plus 24 hours for the glue (estimate)
FinishNone: leave the wood unfinished
Side views of the toy car and pickup truck with lengths, heights, axle positions and window positions.

Tools You Need

  • Band saw or scroll saw (a jigsaw works for the outlines)
  • Drill press, with 13/32 in. and 3/8 in. brad-point bits and a 3/4 in. Forstner bit
  • Printer, scissors, and a glue stick or removable spray adhesive
  • Compass, square, tape measure and pencil
  • Fine-tooth handsaw or miter saw for the dowel
  • Disc or spindle sander, or a sanding block; sandpaper in 120, 180 and 220 grit
  • Wood glue, a damp cloth and a scrap of thin card as a spacer
  • Wood-burning pen or stamp for the tracking mark
  • Safety glasses, hearing protection and a dust mask

Follow your saw and drill maker’s instructions, and clamp the wheels and short pieces rather than holding them by hand.

Materials

  • 2 × 4 × 2 ft. poplar board (S4S hardwood, not construction lumber) (actual 1-1/2 × 3-1/2 in.): 1
  • 1 × 4 × 3 ft. poplar board (actual 3/4 × 3-1/2 in.): 1
  • 3/8 in. × 36 in. hardwood dowel (actual 3/8 in. diameter): 1

Buy the 2 × 4 from the hardwood rack: it is planed poplar with square edges. A construction 2 × 4 is softwood with knots and rounded corners, and it does not suit a toy. Do not use plywood, MDF or treated wood.

The Full-Size Templates

The PDF includes both bodies at full size on one US Letter page, with the hole centers marked. Print it at 100% (Actual size) and check its 1 in. test square before you cut. Draw the wheels with a compass.

A reduced view of the full-size templates for the car and the pickup truck, with crosses for the axle holes and windows.

Cutting Diagram

Cutting diagram: both bodies on a 2 foot poplar 2 by 4, eight wheels on a 1 by 4 and four axles on a dowel.

How to Make Wooden Toy Cars, Step by Step

Step 1: Choose the Wood and Stick On the Templates

Use S4S poplar from the hardwood rack, not a construction 2 × 4: construction lumber is softwood with knots and rounded edges. Pick boards with no knots, cracks or splits. Print the templates at 100% (Actual size), check the 1 in. test square, and stick them to the 2 × 4 with the bottom of each body on one edge. Mark eight 2 in. circles on the 1 × 4 with a compass.

Step 2: Drill the Holes

Drill every hole on a drill press while the boards are whole, with the board clamped flat and a scrap backer underneath. In each body, drill the two axle holes at 13/32 in. right through the 1-1/2 in. thickness, then the windows with the 3/4 in. Forstner bit. At the center of each wheel circle, drill a 3/8 in. hole right through.

Step 2 diagram: the car and truck templates on a 2 by 4, with the axle holes and windows marked for drilling.

Step 3: Cut Out the Bodies and Wheels

Cut the car and truck outlines on a band saw or scroll saw, keeping just outside the line. Cut the wheels just outside their circles and sand them round to the line on a disc or spindle sander. Cut four axles 3-1/4 in. long from the dowel.

Step 4: Round the Edges and Sand

Peel off the paper and sand away any glue left on the wood. Round every edge of the bodies, the window edges, the wheels and the axle ends to about a 1/8 in. radius. Sand all faces with 120, 180 and 220 grit. Check that each axle turns freely in its body holes; sand the axle lightly if it binds.

Step 5: Fit the Wheels and Axles

Push an axle through a body. Put a little glue inside one wheel hole only, slide the wheel on until the axle end is flush with its face, and repeat on the other side. Keep a 1/8 in. card spacer between each wheel and the body while the glue sets, then pull it out. Keep glue out of the body holes. Let the glue cure for 24 hours.

Step 4 diagram: end view of a body, axle and two wheels, with glue only in the wheel holes and card spacers.

Step 6: Check and Mark

Roll each vehicle across the floor: all four wheels should turn and touch the ground. Run your fingers over every edge, window and face for splinters. Burn or stamp your tracking mark on the underside of each body. Leave the wood unfinished.

Toy Safety and the Small Parts Check

Small parts check: the axle beside the 2-1/4 inch test cylinder, and a wheel compared with the 1-1/4 inch opening.
  • Toys designed or sold mainly for children aged 12 and under are children’s products. The US Consumer Product Safety Commission (CPSC) regulates them, whatever the size of the business.
  • The toy safety standard ASTM F963 is mandatory (16 CFR Part 1250). It covers hazards such as sharp points and edges and small parts, and many tests follow drop, pull and twist (use and abuse) tests.
  • This plan is designed for ages 3 and up. Every part is too large to fit fully inside the CPSC small parts test cylinder, 1-1/4 in. wide and 2-1/4 in. long, so no choking hazard warning is needed for small parts.
  • Children’s products need third-party testing at a CPSC-accepted lab and a Children’s Product Certificate (CPC). Small batch manufacturers who register with the CPSC get relief from some third-party tests, but not all.
  • The CPSC has determined that unfinished, untreated solid wood does not need third-party testing for lead content or the heavy metals in ASTM F963. Paint, stain, varnish and other finishes or treatments remove that exemption, and paint and surface coatings must not exceed 90 ppm lead.
  • Each toy needs a permanent tracking label on the toy and its packaging, where practical: who made it, where, when and the batch.

Selling Wooden Toy Cars

Toy cars and trucks are children’s products, so the rules above apply before you sell them, including at craft fairs and on marketplaces. Many wooden cars on the market are painted. Leaving these unfinished keeps the exemption from lead and heavy-metal testing for the wood. The glue is a separate material, so ask your testing lab about it.

Testing is per design, so the car and the truck are two designs. The lab’s use and abuse tests pull and twist the wheels, so test the glued wheels on your own samples first. Pack each toy in a bag or box printed with your tracking label details.

This is a summary to help you plan. It is general information, not legal advice. Read the CPSC pages listed under Sources, or ask the CPSC Small Business Ombudsman, before you sell.

See how to set the final selling price on your craft and how to sell woodworking projects. The top 10 woodcrafts to sell has more ideas.

Download the Printable Wooden Toy Car Plans

The PDF has 9 pages on US Letter paper, with the full-size templates, cut list, cutting diagram, drawings, steps and the toy safety summary. It is free, with no sign-up.

Download the wooden car and truck plans (PDF)

Build status: plan checked by calculation; not yet test-built. Facts checked: November 2026.

Sources


Discover more from AssembleAndEarn.com

Subscribe to get the latest posts sent to your email.

Leave a comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.