Free Wooden Train Plans: Engine, Coal Tender, Stake Car and Caboose

This free plan makes a four-car wooden toy train from poplar blocks and hardwood dowels: an engine, a coal tender, a stake car and a caboose that couple with a peg and tongue. It includes full-size templates, cut list, drawings, steps, the small parts check and the US rules for selling toys. The PDF is free.

Categorized as Woodworking Business Tagged ,

This free plan makes a four-car wooden toy train: an engine, a coal tender, a stake car and a caboose. Each car is built on a poplar 2 × 4 base from glued blocks and hardwood dowels, rolls on 2 in. wheels, and couples to the next with a peg and tongue. You can download the plan and full-size templates as a printable PDF, with no sign-up.

The train is designed for children aged 3 and up. Every dowel is at least 2-1/2 in. long and every wheel is 2 in. across, so no part fits the CPSC small parts cylinder even if it came loose. Wooden trains appear in our list of wooden toys to make and sell. The plan suits a woodworker with a drill press.

A plain wooden toy train: engine with cab and smokestack, coal tender, stake car with dowel stakes, and caboose.
The four cars, coupled.

Wooden Train Plans at a Glance

Length34-1/4 in. coupled
Width5-1/4 in. over the wheels
Height6-11/16 in. at the engine cab
CarsEngine, coal tender, stake car and caboose
Ages3 and up
WoodS4S poplar and hardwood dowels
Skill levelIntermediate
Build timeAbout 10 hours, plus glue time (estimate)
FinishNone: plain wood (see the painting note)
PartNameQuantitySize (T × W × L)Material
ABase41-1/2 × 3-1/2 × see note: Engine 9-1/4, tender 8, stake car 7-1/2, caboose 82 × 4 poplar
BCab layer21-1/2 × 3-1/2 × 4 in.2 × 4 poplar
CRoof23/4 × 4-1/4 × 4-1/2 in.1 × 6 poplar
DBoiler layer21-1/2 × 3-1/2 × 3-3/4 in.2 × 4 poplar
ECoal bin layer21-1/2 × 3-1/2 × 4-1/2 in.2 × 4 poplar
FCaboose body layer21-1/2 × 3-1/2 × 4-1/2 in.2 × 4 poplar
GWheel163/4 × 2 × 2 in.1 × 4 poplar
HAxle83/8 × 3/8 × 5-1/4 in.3/8 in. hardwood dowel
JCoupler peg43/4 × 3/4 × 2-3/4 in.3/4 in. hardwood dowel
KCoupler tongue33/4 × 2 × 3-9/16 in.1 × 6 poplar
LSmokestack13/4 × 3/4 × 3-1/4 in.3/4 in. hardwood dowel
MDome13/4 × 3/4 × 2-1/2 in.3/4 in. hardwood dowel
NStake65/8 × 5/8 × 3-1/2 in.5/8 in. hardwood dowel
PCupola11-1/2 × 2-1/2 × 2-1/2 in.2 × 4 poplar
QCupola roof13/4 × 3-1/4 × 3-1/4 in.1 × 4 poplar
Side view of the coupled wooden train with the length of each car base, the 34 inch overall length and the cab height.
Exploded view of the engine and coal tender: bases, cab, boiler, roof, smokestack, dome, coal bin, wheels and couplers.
Exploded view of the stake car and caboose: bases, stakes, caboose body, roof, cupola, wheels and couplers.

Tools You Need

  • Miter saw or handsaw, and a band saw or jigsaw for the boiler and coal bin profiles
  • Table saw or circular saw with a guide, to rip the caboose layers, cupola and tongues
  • Drill press, with 13/32 in., 5/8 in. and 3/4 in. brad-point bits, 15/16 in. and 1 in. Forstner bits, and a countersink
  • 2 in. hole saw for the wheels, and a 3/8 in. bit to open the wheel holes
  • Four or more clamps
  • Printer, scissors and a glue stick for the templates
  • Sanding block or random orbit sander, files, and sandpaper in 120, 180 and 220 grit
  • Wood-burning pen or stamp for the tracking mark
  • Safety glasses, hearing protection and a dust mask

Follow your saw and drill makers’ instructions, and clamp small parts rather than holding them by hand.

Materials and Hardware

  • 2 × 4 × 8 ft. poplar board (S4S) (actual 1-1/2 × 3-1/2 in.): 1
  • 1 × 6 × 4 ft. poplar board (S4S) (actual 3/4 × 5-1/2 in.): 1
  • 1 × 4 × 4 ft. poplar board (S4S) (actual 3/4 × 3-1/2 in.): 1
  • Hardwood dowel, 3/8 in. × 36 in. (actual 3/8 in.): 2
  • Hardwood dowel, 3/4 in. × 36 in. (actual 3/4 in.): 1
  • Hardwood dowel, 5/8 in. × 36 in. (actual 5/8 in.): 1
  • #8 × 2-1/2 in. flat-head wood screws: 8
  • #8 × 1-1/2 in. flat-head wood screws: 12
  • Wood glue (PVA): 1 bottle
  • Paint: None in the plan (see the painting note)

Buy the boards from the hardwood rack and the dowels in birch or oak. Do not use construction lumber, plywood, MDF or treated wood.

Cutting Diagram

Cutting diagram: bases and blocks on a 2 by 4, roofs and tongues on a 1 by 6, and 16 wheels on a 1 by 4.

How the Couplers and Wheels Work

Each car has a 3/4 in. dowel peg at the back. The tongue on the front of the next car has a 15/16 in. hole that drops over that peg, with enough play for the train to go round corners. The wheels are glued to 3/8 in. dowel axles, and the axles turn in 13/32 in. holes through the base.

Coupler section with the tongue hole over the peg, and an end view of a wheel set with the axle through the base.

How to Make a Wooden Toy Train, Step by Step

The PDF has full-size templates for the cab, boiler, coal bin, caboose body and tongue, and for each base with every hole marked.

Step 1: Choose the Wood

Buy S4S poplar from the hardwood rack and hardwood dowels (birch or oak). Pick boards with no knots, cracks or splits. Do not use construction lumber, plywood, MDF or treated wood.

Step 2: Cut the Parts

Cut the four bases (A) from the 2 × 4: engine 9-1/4 in., tender 8 in., stake car 7-1/2 in. and caboose 8 in. Cut the block layers (B, D, E, F) and the cupola (P) from the same board, then rip the caboose layers to 3 in. and the cupola to 2-1/2 in. Cut the roofs (C) from the 1 × 6, and rip three tongues (K) 2 in. wide. Cut the dowels: 8 axles at 5-1/4 in., 4 pegs at 2-3/4 in., the stack at 3-1/4 in., the dome at 2-1/2 in. and 6 stakes at 3-1/2 in. Follow the cutting diagram.

Step 3: Glue Up the Blocks

Glue each pair of layers face to face: cab (B), boiler (D), coal bin (E) and caboose body (F). Clamp them overnight. Stick on the templates and cut the boiler and coal bin profiles with a band saw or jigsaw. Sand the cut edges smooth.

Step 4: Drill the Holes

Stick the base templates to the bases. On the drill press, drill the axle holes 13/32 in. right through each base from side to side, 9/16 in. up from the bottom. Drill the 3/4 in. peg holes and the 5/8 in. stake holes 1-1/4 in. deep, not through. Drill the 1 in. cab window and caboose portholes right through the glued blocks, with a scrap block behind them. Drill the 3/4 in. stack and dome holes 1 in. deep in the boiler, and the 15/16 in. hole in each tongue.

Step 5: Fit the Wheels and Axles

Cut 16 wheels from the 1 × 4 with the 2 in. hole saw, and open each centre hole to 3/8 in. Sand the wheel edges round. Push an axle through a base, put glue inside one wheel only, and press the wheel on until the axle end is flush. Repeat on the other side with a piece of card as a 1/8 in. spacer, so the wheels turn freely. Do not get glue in the axle holes.

Step 5 diagram: wheels and axles on a car base, the wheels pulled out to show the axle through the base.

Step 6: Assemble the Engine

Glue the cab and the boiler to the engine base, lined up on the template marks. Drill and countersink two holes up through the base under each block and drive #8 × 2-1/2 in. screws. Glue and screw the cab roof on with two #8 × 1-1/2 in. screws, heads flush. Glue the smokestack and dome into their holes.

Step 6 diagram: the engine cab, boiler, roof, smokestack and dome fitted to the engine base.

Step 7: Assemble the Other Cars

Glue and screw the coal bin to the tender base and the caboose body to the caboose base, the same way. Glue and screw the caboose roof, glue the cupola on top of it, then glue and screw the cupola roof. Glue the six stakes into the stake car, standing straight.

Step 8: Fit the Couplers

Glue a peg into the hole at the back of every base, standing 1-1/2 in. above it. Glue each tongue on top of the front of the tender, stake car and caboose bases, 1-1/2 in. on, and drive two #8 × 1-1/2 in. screws down through it, heads flush. Let the glue cure for 24 hours.

Step 7 diagram: a coupler peg at the back of the stake car base and a tongue with a hole on the front.

Step 9: Round Every Edge and Sand

Round every edge and corner to about a 1/8 in. radius, including the dowel ends, the wheel edges and the tongue ends. Sand all faces with 180 and 220 grit. Check that no screw tip comes through and every screw head is flush.

Step 10: Check and Mark

Couple the cars and pull the train across the floor: every wheel should turn and touch the ground. Pull hard on every dowel and wheel: none should move. Burn or stamp your tracking mark under each base.

Painting the Train

  • The plan leaves the train as plain, unfinished wood. The CPSC exemption from lead and heavy-metal testing covers unfinished, untreated wood, so plain wood keeps testing simpler.
  • If you want a painted train like the one on the cover, use a paint labelled for toys. Paint or any similar coating on a children’s product must not contain more than 90 parts per million of lead, and a CPSC-accepted lab must test it.
  • Painted toys also need the ASTM F963 test for heavy metals in surface coatings. Paint every train you sell with the same paint you had tested.
  • Paint the blocks and roofs before you glue them on, and keep paint out of the axle holes and off the dowel ends that go into holes.

Toy Safety and the Rules for Selling

Small parts check: the shortest dowel, a stake and a wheel beside the CPSC small parts test cylinder.
  • Toys designed or sold mainly for children aged 12 and under are children’s products. The US Consumer Product Safety Commission (CPSC) regulates them, whatever the size of the business.
  • The toy safety standard ASTM F963 is mandatory (16 CFR Part 1250). It covers hazards such as sharp points and edges and small parts, and many tests follow drop, pull and twist (use and abuse) tests.
  • This plan is designed for ages 3 and up. Every part is too large to fit fully inside the CPSC small parts test cylinder, 1-1/4 in. wide and 2-1/4 in. long, so no choking hazard warning is needed for small parts.
  • Children’s products need third-party testing at a CPSC-accepted lab and a Children’s Product Certificate (CPC). Small batch manufacturers who register with the CPSC get relief from some third-party tests, but not all.
  • The CPSC has determined that unfinished, untreated solid wood does not need third-party testing for lead content or the heavy metals in ASTM F963. Paint, stain, varnish and other finishes or treatments remove that exemption, and paint and surface coatings must not exceed 90 ppm lead.
  • Each toy needs a permanent tracking label on the toy and its packaging, where practical: who made it, where, when and the batch.

Selling Wooden Trains

A toy train is a children’s product, so the rules above apply before you sell it, including at craft fairs and on marketplaces. Testing is per design: build every train from the same wood, dowels, glue and screws as the tested one, and treat a painted version as a separate design. Because the cars couple with a peg and tongue, you can also sell extra cars that fit the same train.

This is a summary to help you plan. It is general information, not legal advice. Read the CPSC pages listed under Sources, or ask the CPSC Small Business Ombudsman, before you sell.

See how to set the final selling price on your craft and how to sell woodworking projects. The top 10 woodcrafts to sell has more ideas.

Download the Printable Wooden Train Plans

The PDF has 17 pages on US Letter paper, with the full-size templates, cut list, cutting diagram, drawings, steps and the toy safety rules. It is free, with no sign-up.

Download the wooden train plans (PDF)

Build status: plan checked by calculation; not yet test-built. Facts checked: November 2026.

Sources


Discover more from AssembleAndEarn.com

Subscribe to get the latest posts sent to your email.

Leave a comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.