Free Dollhouse Furniture Plans: Bedroom, Living Room and Kitchen Sets

This free plan makes three room sets of chunky wooden dollhouse furniture for ages 3 and up: a bedroom, a living room and a kitchen, thirteen pieces in all. It includes full-size templates, a cut list, a cutting diagram, drawings, steps and the US rules for selling toys. The PDF is free.

Categorized as Woodworking Business Tagged ,

This free plan makes three room sets of chunky wooden dollhouse furniture: a bedroom, a living room and a kitchen. There are twelve designs and thirteen pieces in all, sized for dolls about 5 to 7 in. tall. You can download the plan and full-size templates as a printable PDF, with no sign-up.

Disclaimer: This plan is free and for information only. It has been checked by calculation but has not been test-built. A toy built from this plan has not been safety-tested. Assemble & Earn makes no guarantee that the plan is accurate or complete, or that anything built from it is safe or fit for any purpose. You build from this plan at your own risk. Assemble & Earn accepts no liability for any injury, loss or damage that results.

The furniture is designed for children aged 3 and up. Every part is 3/4 in. thick or more and too big for the CPSC small parts test cylinder, even on its own, and there are no knobs, screws or nails. Dollhouse furniture appears in our list of wooden toys to make and sell.

Wooden dollhouse kitchen set in a room corner: fridge, stove, sink, trestle table and two chairs with heart cut-outs.
The kitchen set.

Dollhouse Furniture Plans at a Glance

No.PieceRoomSize (W × D × H)
1BedBedroom5-1/2 × 8 × 4-1/2 in.
2NightstandBedroom4 × 3-1/2 × 3-3/4 in.
3DresserBedroom6-1/2 × 3-1/2 × 8 in.
4SofaLiving room7 × 3-1/2 × 4-1/4 in.
5ArmchairLiving room4-1/4 × 3-1/2 × 4-1/4 in.
6Coffee tableLiving room5 × 3 × 2-1/2 in.
7BookcaseLiving room4-1/2 × 2-1/2 × 6-1/2 in.
8Kitchen tableKitchen6 × 4 × 3-3/4 in.
9Chair (make 2)Kitchen2-3/4 × 3-1/2 × 4-15/16 in.
10StoveKitchen4 × 3-3/4 × 6 in.
11SinkKitchen4 × 3-3/4 × 6 in.
12FridgeKitchen3-1/2 × 3 × 7-1/2 in.
Ages3 and up
Doll sizeAbout 5 to 7 in.
WoodS4S poplar: 2 × 4, 1 × 6, 1 × 4, 1 × 3 and 1 × 2
Skill levelBeginner to intermediate
Build timeAbout 12 hours for all three rooms, plus glue time (estimate)
FinishNone: leave the wood unfinished

Tools You Need

  • Band saw or scroll saw for the shapes
  • Table saw or circular saw with a guide, to rip the narrow parts
  • Miter saw or handsaw
  • Drill with a 1-1/4 in. Forstner bit (bed headboard) and a 1/4 in. bit (to start the heart cut-outs)
  • Wood-burning pen, V-gouge or a fine saw for the drawer and door lines
  • Clamps or strong rubber bands for gluing
  • Printer, scissors and a glue stick for the templates
  • Sanding block, files, and sandpaper in 120, 180 and 220 grit
  • Safety glasses, hearing protection and a dust mask

Materials

  • 1 × 6 poplar board, 6 ft. (S4S) (actual 3/4 × 5-1/2 in.): 1
  • 1 × 4 poplar board, 8 ft. (S4S) (actual 3/4 × 3-1/2 in.): 1
  • 2 × 4 poplar board, 8 ft. (S4S) (actual 1-1/2 × 3-1/2 in.): 1
  • 1 × 2 poplar board, 4 ft. (S4S) (actual 3/4 × 1-1/2 in.): 1
  • 1 × 3 poplar board, 4 ft. (S4S) (actual 3/4 × 2-1/2 in.): 1
  • Wood glue (PVA)

Buy the boards from the hardwood rack. Do not use construction lumber, plywood, MDF or treated wood.

Cutting Diagram

Cutting diagram for all thirteen pieces on a 2 by 4, a 1 by 6, a 1 by 4, a 1 by 3 and a 1 by 2.

The Three Room Sets

Each piece has an exploded view with its parts lettered as in the cut list. The PDF also has front and side drawings with sizes, and full-size templates for every shaped part.

Bedroom

Bed, nightstand, dresser.

Wooden dollhouse bedroom set in a room corner: bed with a round cut-out headboard, nightstand and dresser with mirror.
The bed, finished and pulled apart: headboard, footboard, mattress board, pillow and quilt.
The nightstand, finished and pulled apart: a two-layer body with a drawer line and a top.
The dresser, finished and pulled apart: a two-layer body with three drawer lines, a top and an oval mirror.

Living room

Sofa, armchair, coffee table, bookcase.

Wooden dollhouse living room set: sofa with cushions, armchair, coffee table and an open bookcase.
The sofa, finished and pulled apart: two arms, seat base, back and two cushions.
The armchair, finished and pulled apart: two arms, seat base, back and one cushion.
The coffee table, finished and pulled apart: top, two arched leg panels and a stretcher.
The bookcase, finished and pulled apart: two sides and four shelves.

Kitchen

Kitchen table, chair (two), stove, sink, fridge.

Wooden dollhouse kitchen set: fridge, stove, sink, trestle table and two chairs with heart cut-outs.
The kitchen table, finished and pulled apart: top, two trestle legs and a stretcher.
A kitchen chair, finished and pulled apart: back with a heart cut-out, two side panels and a seat.
The stove, finished and pulled apart: a two-layer body with an oven door, a cooktop with burners and a back panel.
The sink, finished and pulled apart: a two-layer body with cupboard doors, a counter top and a back panel.
The fridge, finished and pulled apart: two glued layers with door lines.

How to Make Wooden Dollhouse Furniture, Step by Step

Step 1: Choose the Wood

Buy S4S poplar from the hardwood rack. Pick boards with no knots, cracks or splits. Do not use construction lumber, plywood, MDF or treated wood.

Step 1 diagram: a clear board beside a knotted one, plywood, MDF and treated wood crossed out, and a 2 by 4 end measured.

Step 2: Print the Templates and Cut the Parts

Print the template pages at 100% (Actual size) and check the test square. Cut the straight parts to the sizes in the cut list, following the cutting diagram. Rip the narrow parts on the table saw. Stick the templates on the shaped parts and cut them on a band saw or scroll saw, just outside the line.

Step 2 diagram: a template printed at 100 percent, parts measured from the cut list, a push stick, and a headboard cut out.

Step 3: Cut the Openings

Drill the 1-1/4 in. hole in the bed headboard with a Forstner bit over a scrap block. For each chair heart, drill a 1/4 in. starting hole inside the shape, thread the scroll saw blade through it and cut the heart out. Cut the arched openings at the bottom of the legs and panels.

Step 3 diagram: a Forstner bit drilling over scrap, a heart cut from a starting hole, and an arch at the foot of a panel.

Step 4: Glue Up the Blocks

The nightstand, dresser, stove, sink and fridge bodies are two 2 × 4 layers glued face to face. Glue each pair, clamp it, and leave it overnight. The front layer has the toe-kick notch; the fridge has none.

Step 4 diagram: two 2 by 4 layers glued face to face, clamped overnight, and the toe-kick notch on the front layer.

Step 5: Mark the Drawer and Door Lines

Copy the drawer, door, burner and sink lines from the drawings onto the blocks and tops. Burn them in with a wood-burning pen, or cut them 1/16 in. deep with a V-gouge or a fine saw. There are no knobs or handles to come off.

Step 5 diagram: drawer lines and stove burners burned into the wood, and a V-gouge cutting a line 1/16 inch deep.

Step 6: Round the Edges and Sand

Round every outside edge and corner to about a 1/8 in. radius, and file the inside of each opening smooth. Sand every part with 120, 180 and 220 grit before gluing; it is much harder to reach the corners afterwards.

Step 6 diagram: an edge before and after a 1/8 inch rounding, a round file in an opening, and 120 to 220 grit paper.

Step 7: Glue Each Piece Together

Dry-fit each piece, then glue it in the order shown in its exploded view: legs and panels first, then the top or seat, then the backs and cushions. Wipe away squeezed-out glue with a damp cloth. Clamp or wrap each joint with rubber bands for an hour, and leave the glue to cure for 24 hours.

Step 7 diagram: a chair glued in order, legs first, then the seat, then the back, held with rubber bands for an hour.

Step 8: Check and Mark

Pull and twist every part hard: nothing should move. Stand each piece on a flat table: it should not rock. Run your fingers over every edge for splinters. Burn or stamp your tracking mark underneath. Leave the wood unfinished.

Step 8 diagram: a pull test on a glued part, a chair standing level, an edge checked for splinters and a tracking mark.

Toy Safety and the Rules for Selling

  • Toys designed or sold mainly for children aged 12 and under are children’s products. The US Consumer Product Safety Commission (CPSC) regulates them, whatever the size of the business.
  • The toy safety standard ASTM F963 is mandatory (16 CFR Part 1250). It covers hazards such as sharp points and edges and small parts, and many tests follow drop, pull and twist (use and abuse) tests.
  • This plan is designed for ages 3 and up. Every part is too large to fit fully inside the CPSC small parts test cylinder, 1-1/4 in. wide and 2-1/4 in. long, so no choking hazard warning is needed for small parts.
  • Children’s products need third-party testing at a CPSC-accepted lab and a Children’s Product Certificate (CPC). Small batch manufacturers who register with the CPSC get relief from some third-party tests, but not all.
  • The CPSC has determined that unfinished, untreated solid wood does not need third-party testing for lead content or the heavy metals in ASTM F963. Paint, stain, varnish and other finishes or treatments remove that exemption, and paint and surface coatings must not exceed 90 ppm lead.
  • Each toy needs a permanent tracking label on the toy and its packaging, where practical: who made it, where, when and the batch.

Selling Wooden Dollhouse Furniture

Dollhouse furniture is a children’s product, so the rules above apply before you sell it, including at craft fairs and on marketplaces. Testing is per design, so each piece is a design of its own. You can sell single pieces, a room set or all three rooms, built the same way every time. Say the doll size the furniture suits in your listing.

This is a summary to help you plan. It is general information, not legal advice. Read the CPSC pages listed under Sources, or ask the CPSC Small Business Ombudsman, before you sell.

See how to set the final selling price on your craft and how to sell woodworking projects. The top 10 woodcrafts to sell has more ideas.

Download the Printable Dollhouse Furniture Plans

The PDF has 38 pages on US Letter paper, with the full-size templates, cut list, cutting diagram, exploded views, drawings, steps and the toy safety rules. It is free, with no sign-up.

Download the dollhouse furniture plans (PDF)

Disclaimer: This plan is free and for information only. It has been checked by calculation but has not been test-built. A toy built from this plan has not been safety-tested. Assemble & Earn makes no guarantee that the plan is accurate or complete, or that anything built from it is safe or fit for any purpose. You build from this plan at your own risk. Assemble & Earn accepts no liability for any injury, loss or damage that results. Facts checked: November 2026.

Sources


Discover more from AssembleAndEarn.com

Subscribe to get the latest posts sent to your email.

Leave a comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.