Free Wooden Animal Plans: A Bear, Pig and Sheep With Full-Size Templates

This free plan makes three standing wooden animals, a bear, a pig and a sheep, each cut in one piece from a poplar 2 × 6. It includes full-size templates, cut list, cutting diagram, drawings, steps, the small parts check and the US rules for selling toys. The PDF is free.

Categorized as Woodworking Business Tagged ,

This free plan makes three standing wooden animals: a bear, a pig and a sheep. Each one is cut in a single piece from a 1-1/2 in. thick poplar 2 × 6, so there are no glued joints, wheels or loose parts. The thick wood lets each animal stand on its own. You can download the plan and full-size templates as a printable PDF, with no sign-up.

Disclaimer: This plan is free and for information only. It has been checked by calculation but has not been test-built. A toy built from this plan has not been safety-tested. Assemble & Earn makes no guarantee that the plan is accurate or complete, or that anything built from it is safe or fit for any purpose. You build from this plan at your own risk. Assemble & Earn accepts no liability for any injury, loss or damage that results.

The animals are designed for children aged 3 and up, and each is far larger than the CPSC small parts test cylinder. Wooden animals appear in our list of wooden toys to make and sell. The work is band saw cutting and sanding, so the plan suits a beginner.

Three plain wooden animals, a bear, a pig and a sheep, standing on a green rug.
The bear, pig and sheep, cut from one board.

Wooden Animal Plans at a Glance

PartNameQuantitySizeMaterial
ABear17-3/8 × 5-3/16 × 1-1/2 in.2 × 6 poplar
BPig17-7/16 × 4-9/16 × 1-1/2 in.2 × 6 poplar
CSheep16-3/8 × 4-5/8 × 1-1/2 in.2 × 6 poplar
Bear7-3/8 × 5-3/16 in. long and tall
Pig7-7/16 × 4-9/16 in. long and tall
Sheep6-3/8 × 4-5/8 in. long and tall
Thickness1-1/2 in.
WoodS4S poplar
Ages3 and up
Skill levelBeginner
Build timeAbout 3 hours for the set (estimate)
FinishNone: leave the wood unfinished
Side views of the bear, pig and sheep with their lengths and heights, drawn to the same scale.

Tools You Need

  • Band saw (best for 1-1/2 in. stock) or a scroll saw with a heavy blade
  • Printer, scissors, and a glue stick or removable spray adhesive
  • Square, tape measure and pencil
  • Spindle sander or drum sander in a drill, a sanding block, small files
  • Sandpaper in 80, 120, 180 and 220 grit
  • Wood-burning pen or stamp for the tracking mark
  • Safety glasses, hearing protection and a dust mask

Follow your saw maker’s instructions, and keep your fingers to the side of the blade on the tight curves.

Materials

  • 2 × 6 × 4 ft. poplar board (S4S hardwood, not construction lumber) (actual 1-1/2 × 5-1/2 in.): 1

Buy the 2 × 6 from the hardwood rack: it is planed poplar with square edges. A construction 2 × 6 is softwood with knots and rounded corners, and it does not suit a toy. Do not use plywood, MDF or treated wood.

The Full-Size Templates

The PDF includes each animal at full size on its own US Letter page. Print them at 100% (Actual size) and check the 1 in. test square before you cut. Line up the feet with the edge of the board so the grain runs from head to tail.

A reduced view of the full-size templates for the bear, pig and sheep, with the grain direction marked.

Cutting Diagram

Cutting diagram: the bear, pig and sheep laid out along a 4 foot poplar 2 by 6, with room for a second set.

How to Make Wooden Animals, Step by Step

Step 1: Choose the Wood

Use S4S poplar from the hardwood rack, not a construction 2 × 6, which is softwood with knots and rounded edges. Pick a board with no knots, cracks or splits, above all where the legs fall. Do not use plywood, MDF or treated wood. The grain must run along each animal, from head to tail.

Step 1 diagram: a clear board beside a knotted one, plywood, MDF and treated wood crossed out, and the board end measured.

Step 2: Stick On the Templates

Print the three templates at 100% (Actual size) and check each 1 in. test square. Cut around the paper, leaving a margin, and stick each one to the board with the feet on one edge. Leave at least 1/2 in. between the animals. The 4 ft. board has room for a second set.

Step 2 diagram: the bear, pig and sheep templates stuck on a poplar 2 by 6, feet on one edge, grain along the board.

Step 3: Cut Out the Animals

Cut each outline on a band saw, keeping just outside the line. Cut the gap between the legs last: make two straight cuts down the sides of the gap, then nibble out the waste. Saw the tight curves around the ears, snout and tail slowly. Keep your fingers well to the side of the blade.

Step 3 diagram: sawing just outside an animal outline, two straight cuts to clear the leg gap, and sanding to the line.

Step 4: Round Every Edge and Sand

Peel off the paper and sand away any glue left on the wood. Sand the outline smooth to the line with 80 and 120 grit on a spindle sander or drum sander, then round every edge on both faces to about a 3/16 in. radius. File the inside corners between the legs and around the ears. Finish all faces with 180 and 220 grit.

Step 4 diagram: a square edge beside the same edge rounded to a 3/16 inch radius on both faces.

Step 5: Check and Mark

Stand each animal on a flat table: it should stand steady without rocking. If it rocks, sand the feet flat on a sheet of sandpaper laid on the table. Run your fingers over every edge and face for splinters. Burn or stamp your tracking mark on the underside of the belly. Leave the wood unfinished.

Step 5 diagram: an animal standing steady on a table, its feet sanded on flat paper, a tracking mark and no paint.

Toy Safety and the Small Parts Check

Small parts check: the sheep beside the 1-1/4 inch wide CPSC test cylinder, many times larger.
  • Toys designed or sold mainly for children aged 12 and under are children’s products. The US Consumer Product Safety Commission (CPSC) regulates them, whatever the size of the business.
  • The toy safety standard ASTM F963 is mandatory (16 CFR Part 1250). It covers hazards such as sharp points and edges and small parts, and many tests follow drop, pull and twist (use and abuse) tests.
  • This plan is designed for ages 3 and up. Every part is too large to fit fully inside the CPSC small parts test cylinder, 1-1/4 in. wide and 2-1/4 in. long, so no choking hazard warning is needed for small parts.
  • Children’s products need third-party testing at a CPSC-accepted lab and a Children’s Product Certificate (CPC). Small batch manufacturers who register with the CPSC get relief from some third-party tests, but not all.
  • The CPSC has determined that unfinished, untreated solid wood does not need third-party testing for lead content or the heavy metals in ASTM F963. Paint, stain, varnish and other finishes or treatments remove that exemption, and paint and surface coatings must not exceed 90 ppm lead.
  • Each toy needs a permanent tracking label on the toy and its packaging, where practical: who made it, where, when and the batch.

Selling Wooden Animals

Wooden animals are children’s products, so the rules above apply before you sell them, including at craft fairs and on marketplaces. Each animal is one piece of unfinished wood with no glue, paint or other materials, which keeps the exemption from lead and heavy-metal testing for the wood.

Testing is per design, so each animal is a design of its own. You can sell them singly or as a set, cut from the same templates every time. A 4 ft. board makes two sets with a little to spare. Pack each animal or set in a bag or box printed with your tracking label details.

This is a summary to help you plan. It is general information, not legal advice. Read the CPSC pages listed under Sources, or ask the CPSC Small Business Ombudsman, before you sell.

See how to set the final selling price on your craft and how to sell woodworking projects. The top 10 woodcrafts to sell has more ideas.

Download the Printable Wooden Animal Plans

The PDF has 13 pages on US Letter paper, with the full-size templates, cut list, cutting diagram, drawings, steps and the toy safety summary. It is free, with no sign-up.

Download the wooden animal plans (PDF)

Disclaimer: This plan is free and for information only. It has been checked by calculation but has not been test-built. A toy built from this plan has not been safety-tested. Assemble & Earn makes no guarantee that the plan is accurate or complete, or that anything built from it is safe or fit for any purpose. You build from this plan at your own risk. Assemble & Earn accepts no liability for any injury, loss or damage that results. Facts checked: November 2026.

Sources


Discover more from AssembleAndEarn.com

Subscribe to get the latest posts sent to your email.

Leave a comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.